Driver Stepper Motor 2H606T
-
Payment
-
Origin
China Mainland
-
Minimum Order
15
-
Packing
Pieces
- Contact Now Start Order
- Description
Product Detail
2H606T step motor driver
Characteristics :
The motor driver 2H606T is two phase hybrid stepper motor driver , driving nema 23 and nema 24 two phase stepper motor . It has 16 microsteps , MAX micro step is 64 subdivision ; Current range is 1.4A ~ 5.6A , 8 class output current ,current resolution is 0.6A ; with function of half current .over-voltage and over-current protection etc . It is DC power supply , working voltage is 24VDC - 50VDC , voltage shouldn’t be over 50VDC , and not below 20VDC .
Parameters :
Input Power supply : | 24VDC ~50VDC |
Output Current | 1.4A~5.6A |
Drive Way | PWM constant current chopping ,three phase Sine wave output current |
Suitable stepper motor | 57, 60 series two phase stepper motor |
Ambient environment | -10?~55? 15~85%RH?No condensation. Non-corrosive, flammable, explosive, conductive gas, liquid and dust |
Keeping enviroment | -40?~+55?, <93%RH,No condensation, no frost |
Size (L*W*H) | 118*75.5*34 mm |
Net Weight | 0.25 Kg |
Description :
Microstep setting | Users can set the driver Microstep by the SW5-SW8 four switches,total 16 micro-step. When you set the microstep , pls stop the driver working?The setting of the specific Microstep subdivision, please refer to the instructions of the driver panel figure . |
Output current setting | Users can set the driver Microstep by the SW1-SW3 three switches. The setting of the specific Microstep subdivision, please refer to the instructions of the driver panel figure |
Automatic half current function | Users can set the driver half flow function by SW4. "OFF" indicates the quiescent current is set to half of the dynamic current, that is to say, 0.5 seconds after the cessation of the pulse, current reduce to about half automatically. "ON" indicates the quiescent current and the dynamic current are the same. User can set SW6 to "OFF", in order to reduce motor and driver heating and improve reliability. |
signal Interface | PUL+ and PUL- are the positive and negative side of control pulse signal; DIR+ and DIR- are the positive and negative side of direction signal; ENA+ and ENA- are the positive and negative side of enable signal . |
Motor Interface | A+ and A- are connected to a phase winding of motor; B+ and B- are connected to another phase winding of motor. If you need to backward, one of the phase windings can be reversed . |
Power Interface | It uses DC power supply,recommended working voltage is 20-50VDC,power is over 100W . |
Indicator Lightor | There are two indicator lights. Power indicator is green. When the driver power on, the green light will always be lit. Fault indicator is red, when there is over-voltage or over-current fault, the red light will always be lit; after the driver fault is cleared, if re-power the red light will be off . |
Installation | The size of motor driver is 118×75.5×34mm,mounting holes is 112mm?Chest and upright installation are ok,we suggest upright installation. During installation, it should be close to the metal cabinet for heat dissipation. |
Parameters setting :
The motor driver use eight DIP to microstep subdivision , automatic current and half /full current , more details are as below :
Working current setting (OFF=0,ON=1):
Current | SW1 | SW2 | SW3 |
1.4 | 0 | 0 | 0 |
2.1 | 1 | 0 | 0 |
2.7 | 0 | 1 | 0 |
3.2 | 1 | 1 | 0 |
3.8 | 0 | 0 | 1 |
4.3 | 1 | 0 | 1 |
4.9 | 0 | 1 | 1 |
5.6 | 1 | 1 | 1 |
Microstep | SW5 | SW6 | SW7 | SW8 |
200 | 0 | 0 | 0 | 0 |
400 | 1 | 0 | 0 | 0 |
500 | 0 | 1 | 0 | 0 |
800 | 1 | 1 | 0 | 0 |
1000 | 0 | 0 | 1 | 0 |
1250 | 1 | 0 | 1 | 0 |
1600 | 0 | 1 | 1 | 0 |
2000 | 1 | 1 | 1 | 0 |
2500 | 0 | 0 | 0 | 1 |
3200 | 1 | 0 | 0 | 1 |
4000 | 0 | 1 | 0 | 1 |
5000 | 1 | 1 | 0 | 1 |
6400 | 0 | 0 | 1 | 1 |
8000 | 1 | 0 | 1 | 1 |
10000 | 0 | 1 | 1 | 1 |
12800 | 1 | 1 | 1 | 1 |
Interface of motor driver :
Note : 1.VCC is 5V , R is short connection .
1.VCC is 12V , R is 1K , over than 1/8W resistance .
2.VCC is 24V , R is 2K , over than 1/8w resistance , need connect in the end of signal of controller .
Interface connection and installing size :
- High Torque Nema 23 Stepper Motor 425 Oz In 1 Pieces / (Min. Order)
- Nema 23 Stepper Motor 1.26N.m 1 Pieces / (Min. Order)
- Nema 23 Stepper Motor 1.89N.m 1 Pieces / (Min. Order)
- 110V Stepper Motor Driver 2H1106T 1 Pieces / (Min. Order)
- 220V Nema 34 Stepper Motor Driver 2H2208T 1 Pieces / (Min. Order)
- Brushless Motor Driver 15 Pieces / (Min. Order)
- 2000W Servo Motor Drivers 15 Pieces / (Min. Order)
- 1500W Servo Motor Driver 15 Pieces / (Min. Order)
- Three Phase Motor Driver MD-3008B 15 Pieces / (Min. Order)
- Nema 52 Stepper Motor Driver 3008A 15 Pieces / (Min. Order)
- Low Voltage Motor Driver 3DM683 15 Pieces / (Min. Order)
- Motor Driver For Nema 2M423A 15 Pieces / (Min. Order)
- Small Stepper Motor Driver 2M422A 15 Pieces / (Min. Order)
- 220V Motor Driver 2H2208T 15 Pieces / (Min. Order)
- Motor Driver 2H1106T 15 Pieces / (Min. Order)
- AC Stepper Motor Driver 2H8006T 15 Pieces / (Min. Order)
- 1.2 Degree Nema 52 Stepper Motor 1303P 15 Pieces / (Min. Order)
- 1.8 Degree Nema 52 Stepper Motor 130STH 15 Pieces / (Min. Order)
- Nema 42 Stepper Motor Round Shape 1103P 15 Pieces / (Min. Order)